MODEL H8110
9 DRAWER EURO STYLE
WORKBENCH-BIRCH
INSTRUCTIONS
Assembly
refer to the last page of these instructions to
inventory your shipment for ease of assembly.
To assemble the workbench:
1. position the right side leg (C) on the floor
so the Up arrow is pointing upward and the
Front arrow points to the front, as shown in
figure 12.
2. place the two lower cross braces (e) on the
floor so the slots face each other, as shown
in figure 12.
figure 11. model h8110 Birch Workbench.
Specifications
Finish..........................................Lacquer sealed
drawer slides ...................................Ball Bearing
number of drawers ........................................... 9
Front Vise size .....................................193⁄4" x 7"
end Vise size ............................................6" x 6"
overall size ..............841⁄2"W x 2411⁄16"d x 341⁄4"h
drawer size.....................153⁄8"W x 137⁄8"d x 4"h
storage shelf size.....................551⁄2"W x 181⁄2"d
shipping Weight ......................................367 lbs.
C
E3
E2
E4
E
Safety & Limitations
E
•
•
•
maximum workbench table load is 500 lbs.
do not stand or climb on the workbench.
do not apply an unbalanced load on the table
that could result in the workbench tipping.
Keep unsupervised children away from the
workbench.
do not stand or climb on the workbench.
do not use workbench outdoors or in wet or
damp locations.
figure 12. right leg and cross brace installation.
3. insert the barrel nuts (e4) (figure 12) into the
ends of the cross braces so the slotted end
faces outward and the screwdriver slots are
aligned horizontally with the direction of the
cross braces.
•
•
•
4. insert the cross braces into the mortised
holes into the right-side leg, as shown in
figure 12.
•
•
do not overload the vises or use cheater
pipes on the vise handles to increase lever-
age.
do not weld on this bench.
Copyright © JULy 2009 By grizzLy indUstriaL, inC.
WARNINg: NO pORTION Of THIS MANUAL MAY BE REpRODUCED IN ANY SHApE
OR fORM WITHOUT THE WRITTEN AppROvAL Of gRIzzLY INDUSTRIAL, INC.
(For modeLs manUFaCtUred sinCe 7/09) #Cr12018 printed in China
14. insert the bolts through the left-side leg,
tighten with a 5mm hex wrench, and all other
barrel bolts at this time.
19. insert the guide rods and leadscrew through
the holes in the wood block (g) (figure 19).
thread the leadscrew into the vise support
until the wood block is slightly snug against
the table and flush with the table top.
15. align the pre-drilled holes in the underside
of the work bench table top (a) with the pre-
drilled holes in the legs.
Lead Screw
Guide Rod
Vise Support
Block
16. place a flat washer (e2) onto each of the
four 2" wood screws (e8). From the table
underside, insert the screws in the pre-drilled
holes, and use a 4mm hex wrench to tighten
the wood screws.
Wood Block
A
G
17. Using a standard screwdriver, attach the right
(sr) and left (sL) drawer sides to the drawer
backs (sB). then slide the drawer bottoms
(Bp) into the drawer side grooves (figure 17)
until they are fully seated in the grooves.
Flush
Wood Block
Flush
G
A
Vise Plate
BP
figure 19. table vise installation.
SL
20. Keeping the wood block flush with the table
top (figure 19), drill two 5⁄64" holes 17⁄16" deep
through the vise plate mounting holes and
into the wood block.
SB
Rotate
SR
with
Screwdriver
to Lock
21. secure the vise plate to the wood block with
two (e10) #5 x 17⁄16" wood screws (figure
19). install a cotter pin in the end of the lead-
screw, and bend one pin leg to 90 degrees.
figure 17. initial drawer assembly.
18. install the drawer fronts (sF) (figure 18), the
handles (e5), the screws (e1), and insert the
drawers into the work bench drawer slides.
22. insert the tail vise wood block into the vise
support block (figure 20). insert the tail vise
leadscrew through the holes in the wood
block and the vise support block at the edge
of the table.
E5
E1
Vise Support
Block
A
SF
Wood Block
J
figure 20. tail vise installation.
figure 18. Final drawer assembly.
model h8110 (mfg. since 7/09)
23. turn the tail vise handle clockwise until the
wood block just touches the table, and attach
the vise plate as outlined in Step 21.
-3-
parts
parts Breakdown and Inventory
J
C
a
d
F
g
d
B
e
e
h
F
sF
sL
Bp
fastener Kit
e4
e5
e1
e7
e8
sB
sC
sr
e2
ss
sd
e9
e10
e6
e3
REf pART
DESCRIpTION
QTY
1
ph8110018 BenCh top
a
B
ph8110019 LeFt side Leg
ph8110020 right side Leg
1
1
C
fastener Kit part Numbers
ph8110001 handLe sCreW
pW01m FLat Washer 8mm
QTY
ph8110021 top Cross BraCe
ph8110022 Bottom Cross BraCe
ph8110023 Cross paneL
2
d
e1
e2
e3
e4
e5
e6
e7
e8
e9
e10
18
12
8
2
e
1
F
ph8110003 BarreL BoLt 3.5"
ph8110004 BarreL nUt
ph8110005 handLe
ph8110024 Front Vise
1
g
h
8
ph8110025 draWer sUpport
ph8110026 taiL Vise
2
9
J
1
paW05m
paW04m
heX WrenCh 5mm
heX WrenCh 4mm
1
ss
sC
sL
sr
sB
Bp
sF
sd
ph8110010 BraCKet reCeiVer
ph8110011 BraCKet
36
36
9
1
ph8110008 Wood sCreW 2"
ph8110009 Cotter pin
ph8110030 Wood sCreW #5 x 17⁄16"
4
ph8110012 draWer side LeFt
ph8110013 draWer side right
ph8110014 draWer side BaCK
ph8110015 draWer Bottom
ph8110016 draWer side Front
ph8110017 draWer sLide
2
9
4
9
9
9
18
-4-
model h8110 (mfg. since 7/09)
|